- 您现在的位置：买卖IC网 > Sheet目录871 > OKY-T/3-D12P-C (Murata Power Solutions Inc)CONV DC/DC 15W 12VIN 3AOUT
OKY-T/3,T/5-D12 Series
Adjustable Output 3 and 5-Amp DOSA-SMT DC/DC Converters
Speci?cation Notes, Cont.:
Soldering Guidelines
(5)
(6)
(7)
(8)
The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced
to -Input Common. A logic gate may also be used by applying appropriate external voltages which do not
exceed +Vin.
Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected
setting.
For W5 models, the Input Voltage must exceed the Output Voltage at all times by the ratio of Vin >= (1.15 x
Vout). Please see the separate W5 data sheet.
Output noise may be further reduced by adding an external ?lter. At zero output current, the output may
contain low frequency components which exceed the ripple speci?cation. The output may be operated
Murata Power Solutions recommends the speci?cations below when installing these
converters. These speci?cations vary depending on the solder type. Exceeding these
speci?cations may cause damage to the product. Your production environment
may differ therefore please thoroughly review these guidelines with your process
engineers.
inde?nitely with no load.
(9) All models are fully operational and meet published speci?cations, including “cold start” at –40? C.
(10) Regulation speci?cations describe the deviation as the line input voltage or output load current is varied
Reflow Solder Operations for surface-mount products (SMT)
For Sn/Ag/Cu based solders:
from a nominal midpoint value to either extreme.
(11) Other input or output voltage ranges will be reviewed under scheduled quantity special order.
(12) Maximum PC board temperature is measured with the sensor in the center of the converter.
(13) Do not exceed maximum power speci?cations when adjusting the output trim.
(14) The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external
output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will
reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may
require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please
refer to the Output Capacitive Load Application Note.
(15) Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times.
Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will
attempt to recover when the input is brought back into normal operating range.
(16) The outputs are not intended to sink appreciable reverse current.
(17) “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output.
Preheat Temperature
Time over Liquidus
Maximum Peak Temperature
Cooling Rate
For Sn/Pb based solders:
Preheat Temperature
Time over Liquidus
Maximum Peak Temperature
Cooling Rate
Less than 1 oC. per second
45 to 75 seconds
260 oC.
Less than 3 oC. per second
Less than 1 oC. per second
60 to 75 seconds
235 oC.
Less than 3 oC. per second
If the overcurrent condition still exists, the restart current will be removed and then tried again. This short
current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter
immediately recovers normal operation.
Recommended Lead-free Solder Re?ow Pro?le
Output Voltage Adustment
The output voltage may be adjusted over a limited range by connecting an
external trim resistor (Rtrim) between the Trim pin and Ground. The Rtrim
250
200
Peak Temp.
235-260° C
resistor must be a 1/10 Watt precision metal ?lm type, ±1% accuracy or
better with low temperature coef?cient, ±100 ppm/oC. or better. Mount the
resistor close to the converter with very short leads or use a surface mount
trim resistor.
150
100
Soaking Zone
120 sec max
Re?ow Zone
time above 217° C
45-75 sec
In the tables below, the calculated resistance is given. Do not exceed the
50
<1.5° C/sec
Preheating Zone
High trace = normal upper limit
Low trace = normal lower limit
speci?ed limits of the output voltage or the converter’s maximum power
240 sec max
rating when applying these resistors. Also, avoid high noise at the Trim
input. However, to prevent instability, you should never connect any capaci-
0
0
30
60
90
120
150
180
210
240
270
300
tors to Trim.
OKY-T/3-D12, -T/5-D12
High trace = normal upper limit
Time (sec)
Output Voltage
5.0 V.
3.3 V.
2.5 V.
2.0 V.
1.8 V.
1.5 V.
1.2 V.
1.0 V.
0.7525 V.
Calculated Rtrim (KΩ)
1.472
3.122
5.009
7.416
9.024
13.05
22.46
41.424
∞ (open)
Low trace - normal lower limit
Resistor Trim Equation, D12 models:
R TRIM ( ? ) = _____________
10500
V OUT – 0.7525V
–1000
www.murata-ps.com/support
MDC_OKY-T/3,T/5-D12 Series.B15 Page 5 of 21
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
OKY-T/3-W5N-C
CONV DC/DC 10.9W 5VIN 3AOUT SMD
OKY2-T/16-D12P-C
CONV DC/DC 80W 12VIN 16AOUT SMD
OKY2-T/16-W5P-C
CONV DC/DC 52.8W 5VIN 16AOUT SMD
OTBH156KNPIR-F
CAP FILM 15UF 1.5KVDC QC TERM
P-120AS/A22
BATT NICAD 4/5A 1200MAH S TYPE
P-120SCJS/A02T
BATT 1200MAH 4/5SC NICAD W/TAB
P-130SCS/A06T
BATTERY 1300MAH SC NICAD W/TAB
P-140AS/A16T
BATTERY NICAD A SIZE W/TAB
相关代理商/技术参数
OKY-T/3-W5N-C
功能描述:DC/DC转换器 5Vin 0.7525-3.63Vout 3A 10.9W NegPolarity
RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/3-W5P-C
功能描述:DC/DC转换器 5Vin 0.7525-3.63Vout 3A 10.9W PosPolarity
RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/5-D12N-C
功能描述:DC/DC转换器 12Vin 0.75-5.5Vout 5A 25.5W Neg logic
RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/5-D12P-C
功能描述:DC/DC转换器 12Vin 0.75-5.5Vout 5A 25.5W Pos logic RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/5-W5N-C
功能描述:DC/DC转换器 5Vin 0.7525-3.63Vout 5A 18W Neg Polarity
RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T/5-W5N-C
制造商:Murata Power Solutions 功能描述:DC/DC Converter
OKY-T/5-W5P-C
功能描述:DC/DC转换器 5Vin 0.7525-3.63Vout 5A 18W Pos Polarity
RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
OKY-T10
制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Programmable DOSA-SMT 10/16-Amp DC/DC Converters